Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum http://www.ducatittandf1.com/
....what's your guess? http://www.ducatittandf1.com/viewtopic.php?f=10&t=11793	Page 1 of 3

---

Author:	Wolf [ Sun May 27, 2018 10:59 am ]
Post subject:	....what's your guess?
...that was an abrupt end to a nice tour planned heading to the Dolomites. After shifting down from neutral to the first gear a loud bang occured and the clutch had no more friction. Obviously, the spring retainer of the clutch went off. I hoped that might have been an easy repair on the roadside - until I found a roller and piece of aluminium. ..how found this roller the way to that part of the motor? Regards Wolf Attachments: File comment: ...when the world was perfect...and: a cat is hidden is this picture :-) ...auf diesem Bild ist eine Katze versteckt....jpg [ 670.41 KiB | Viewed 11534 times ] panne2.jpg [ 290.5 KiB | Viewed 11534 times ] panne1.jpg [ 296.22 KiB | Viewed 11534 times ] panne3.jpg [ 347.43 KiB | Viewed 11534 times ]

---

Author:	Cal [ Sun May 27, 2018 11:46 pm ]
Post subject:	Re: ....what's your guess?
Cool bike.....sorry to hear about your troubles. I hope its something minor!!! I dont really have a guess as I am not a Pantah expert, someone on here will know for sure. I have never been in to the bottom end of a pantah, if I were to guess from the picture, looks like a piece of case and maybe a dowel?

---

Author:	ducadini [ Mon May 28, 2018 3:17 am ]
Post subject:	Re: ....what's your guess?
Looks more like one of the bevel's clutch thingies. Couldn't find anything Pantah related. Did You repair it and got on with Your tour of the Dolomiti ? ciao ducadini

---

Author:	Wolf [ Mon May 28, 2018 7:43 am ]
Post subject:	Re: ....what's your guess?
...I didn't dare to continue, because I'm quite sure that the roller comes from the bearing #32 I think I was lucky that the roller found ist way to the clutch cover, otherwise I would have made the Sella Ronda - which is really fun...did it in the past with the 900 Super Sport (bevel) as well with the BMW R 80 G/S. I was curious about the TT2 experience - next year... Cheers Wolf Attachments: page32.jpg [ 89.22 KiB | Viewed 11480 times ]

---

Author:	flattop900 [ Mon May 28, 2018 9:11 am ]
Post subject:	Re: ....what's your guess?
Hey Wolf... I assume that is not a very common place for a bearing failure. Be sure to post what you find after you open up that engine. Regards... Flattop

---

Author:	Wolf [ Mon May 28, 2018 9:17 am ]
Post subject:	Re: ....what's your guess?
...I promise to do that - but since I have 750 motor ready to bolt in this will be winter.... Attachments: IMG_20170114_155048.jpg [ 173.06 KiB | Viewed 11471 times ]

---

Author:	flattop900 [ Mon May 28, 2018 9:26 am ]
Post subject:	Re: ....what's your guess?
Bellissimo !!!!

---

Author:	618F1 [ Mon May 28, 2018 9:00 pm ]
Post subject:	Re: ....what's your guess?
Hallo Wolf. Did you switch to roller bearing from stock ball bearing (as suggested by Cranky) there? If not.......then how did a roller get out of there? MikeV

---

Author:	Wolf [ Tue May 29, 2018 10:47 am ]
Post subject:	Re: ....what's your guess?
Mike, I'm not sure if the bearings were original or modified... is it advisable to go to roller bearings? I was not aware of that. Wolf

---

Author:	flattop900 [ Wed May 30, 2018 9:10 am ]
Post subject:	Re: ....what's your guess?
Hi Wolf.... Another potential source of the roller you found. The 600SL parts manual shows two "rollers" inside the main shaft. (#27) These are not present in the F1, Alazzurra or Elefant manuals. So do they actually perform some sort of rotary task or are they just plugs in a shaft that is drilled all the way through? If this is your mystery roller the question has to be asked again.... How did it get out of there? Attachments: F1 GB.jpg [ 237.4 KiB | Viewed 11378 times ] 600SL GB.jpg [ 93.32 KiB | Viewed 11379 times ] Ala GB.jpg [ 130.45 KiB | Viewed 11379 times ]

---

Page 1 of 3	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/