Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum
http://www.ducatittandf1.com/

Piston-Rings for 80mm Bore-Diam. (Forged E Pistons)
http://www.ducatittandf1.com/viewtopic.php?f=10&t=1661
Page 1 of 1

Author:  hein [ Wed Dec 28, 2011 12:11 pm ]
Post subject:  Piston-Rings for 80mm Bore-Diam. (Forged E Pistons)

Good evening!

Over christmas I have stripped my 600cc TT2 engine due to problems with some oil blows in the exhaust gas. I found out that the second compression ring of the rear cylinder was broken.The pistons are AE type forged HC pistons with 80mm bore (500cc pantah engine bored out to approx. 600cc).

Now, due to the fact that the engine was rebuild not too long ago and everything else looks pretty well, - I bought the road legal Maltry TT2 some while ago -, I would like just to replace the ring (s) !!

Is there anyone who can tell me a supplier to buy ring sets or even sell me some???
Until now I wasn´t succesful in Germany.The ring thickness is 1,68mm.

Thank you very much for iany information and help.

Best regards

Hein

Author:  herb [ Wed Dec 28, 2011 4:04 pm ]
Post subject:  Re: Piston-Rings for 80mm Bore-Diam. (Forged E Pistons)

hello Hein

try this one http://www.lesegmentab.com/fr/pour-nous-contacter.html

It was recommended on a french forum, but I have no personal experience.

kind regards
herb

Author:  Poison [ Mon Jan 02, 2012 5:21 am ]
Post subject:  Re: Piston-Rings for 80mm Bore-Diam. (Forged E Pistons)

Hiya Hein,


I noticed this today:

http://www.ebay.co.uk/itm/DUCATI-MONSTE ... 579wt_1292

you would however be advised to ask the seller about bore size and ring dimensions before bidding......... ;)



Poison

Author:  hein [ Mon Jan 02, 2012 2:59 pm ]
Post subject:  Re: Piston-Rings for 80mm Bore-Diam. (Forged E Pistons)

Hi Poison, thanks very much for the hint and the link.
I will try to find to find out.

Best regards to you

Hein

Author:  loudbike [ Sat Jan 07, 2012 9:04 am ]
Post subject:  Re: Piston-Rings for 80mm Bore-Diam. (Forged E Pistons)

Hello Hein:

We've got some stock (AE) Pantah 600 rings on the store at http://www.loudbikestore.com/066147493-piston-ring-set-80mm-ducati-2v-belt-drive-twins-600-pantah-p-14150.html. If you can give me some measurements off your existing rings, I'll check to see if they might fit..

Regards,

Author:  hein [ Sat Jan 07, 2012 5:54 pm ]
Post subject:  Re: Piston-Rings for 80mm Bore-Diam. (Forged E Pistons)

Hi Steve, hi TT2 fans!

Thank you for the replies on my request. Meanwhile the problem is solved, I could replace the scnd. ring by a ring of a BMW car engine.

Thank you for the support - the issue is closed.

Hein

Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/