Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum http://www.ducatittandf1.com/ |
|
Aussie TT2 track bike build http://www.ducatittandf1.com/viewtopic.php?f=10&t=2434 |
Page 17 of 24 |
Author: | brad black [ Thu Jul 11, 2013 9:03 am ] |
Post subject: | Re: Aussie TT2 track bike build |
the pressure plate pushes the posts which moves the plate at the rear off the pack. the springs push back against the hub. |
Author: | 618F1 [ Thu Jul 11, 2013 9:59 am ] |
Post subject: | Re: Aussie TT2 track bike build |
Yes, they bottom out on the six posts; do not over-torque, the springs keep pressure on this all the time. Without the pressure plate and springs installed you should have at least 1/8th-inch clearance between the outside surface of the top disc and the inner side of the big circle clip. Once everything is installed that will go away and it will be too tight to push by hand. MikeV |
Author: | Pantah600 [ Fri Jul 12, 2013 7:04 am ] |
Post subject: | Re: Aussie TT2 track bike build |
Thanks Brad & MikeV, superb info & knowledge. I must have loosened the pressure plate bolts slightly before I took the photos, so that is what confused me. After talking to a chap at work, he too suggested the plate needs to bottom out on the posts and the bolts torqued up to only 10Nm. Otherwise, it's off at the post! You are correct MikeV, the clutch assembly cannot be moved by hand. When I assembled the clutch pack, 2 steel discs were slightly tight to slide along the splines. The hub shows no signs of notching as does the basket. So, I filed them ever so slightly and now they slide along the splines nicely. I thought I needed to do this so the clutch discs didn't drag. I oiled the friction plates and discs. All good. I will be putting up some photo's of the engine build shortly. I'm so close now. I just wish I had more time during the day! Cheers, Steve |
Author: | Pantah600 [ Thu Aug 22, 2013 5:02 pm ] |
Post subject: | Re: Aussie TT2 track bike build |
Gents, I'm close, very close to firing the engine up for the first time in a long time. However, I need some photos showing the wiring and cabling routes. I've checked out Carlo's website under restorations, but not all the images show the path of the cables & wiring. Can anybody assist here please? Thanks, Steve P.S. I have taken photo's of the build thus far. I just haven't had the time to load them up. And, I'm on a war path to finish it. |
Author: | graeme [ Thu Aug 22, 2013 7:09 pm ] |
Post subject: | Re: Aussie TT2 track bike build |
Hello Steve, Correct or not, this is what I did,,,,, From the throttle, both cables aim down and curve back up then the front cable goes between the steering head and the right fork into the cut out in the tank and onto the front carb. The rear cable goes into the cutout in the left side of the tank then over the top of the frame cross brace (where the top of the shock is attached) then down to the rear carb. The clutch (mine is hydraulic) goes from the lever to the right of the steering head then between the top frame and tank, over the top cross brace then down to the clutch. You may have to look at another way if you have a cable clutch. Graeme |
Author: | Pantah600 [ Fri Aug 23, 2013 9:40 am ] |
Post subject: | Re: Aussie TT2 track bike build |
Sir Graeme, That, my good man is perfectly explained! Could you take a shot of your wiring plate at the front to show your routing please? The main concentration of wires are up the front, so their length doesn't have to be long. I'm modifying a standard Bosch terminal block wiring harness so that it is shorter and set out as shown in previous pages...somewhere. I'm waiting on my local engineering firm to modify the standard Pantah swing arm jaws so I can assembly the rear end. The main focus is getting the engine fired up.....hopefully, not literally! Thanks again Graeme. Cheers, Steve |
Author: | graeme [ Fri Aug 23, 2013 6:26 pm ] |
Post subject: | Re: Aussie TT2 track bike build |
Mine is Kokisan from a '95 not Bosch so it will be not what you are looking for. If its of any help I can send a picture, just ask. Graeme |
Author: | Pantah600 [ Fri Sep 13, 2013 3:02 am ] |
Post subject: | Re: Aussie TT2 track bike build |
Folks, it's almost there... Engine photos will be here shortly. Suffice to say, when one is nearing completion...everything starts to fall apart. Well, not everything, but the little important things.... Anyway, we'll start off with the pre-assembled engine installed... Attachment: Other side.... Attachment: Oooh, that's a bit close...what happened there.... Attachment: Dremel them! Attachment: More to come... |
Author: | Pantah600 [ Fri Sep 13, 2013 3:09 am ] |
Post subject: | Re: Aussie TT2 track bike build |
continued... Ahh, cleaned up the little 36's... Attachment: Rear 36...ohh, damn it close again...see the bell mouth slightly bent.... Attachment: Ahhh, the jaws came back from the machine shoppe... Attachment: Well....let's go crazy! Attachment: Attachment: Attachment: Attachment: Attachment: Now, we just need a throttle.... Cheers, Steve |
Author: | graeme [ Fri Sep 13, 2013 3:51 am ] |
Post subject: | Re: Aussie TT2 track bike build |
Looking Good! The last 5% takes 90% of the time,,,,,,,,, |
Page 17 of 24 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |