Here it is!
Thanks Lou!!
| Attachments: |
|
rwheel.JPG [ 758.14 KiB | Viewed 1268 times ] |
| Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum http://www.ducatittandf1.com/ |
|
| wtb cush for a 4.5 marchesini http://www.ducatittandf1.com/viewtopic.php?f=22&t=10692 |
Page 1 of 2 |
| Author: | huit [ Thu Nov 07, 2013 9:03 pm ] |
| Post subject: | wtb cush for a 4.5 marchesini |
Like the title says, I am looking for a cush for wheel i just picked. I will make one if i need too, just hoping somebody has one stashed away! Thanks Paul |
|
| Author: | ducttf1 [ Thu Nov 07, 2013 10:04 pm ] |
| Post subject: | Re: wtb cush for a 4.5 marchesini |
Hi Paul, my old Marchesini's had a Ducati style bucket cush. Do you have a picture of your wheel? Lou |
|
| Author: | huit [ Thu Nov 07, 2013 10:30 pm ] | ||
| Post subject: | Re: wtb cush for a 4.5 marchesini | ||
Here it is! Thanks Lou!!
|
|||
| Author: | wdietz186 [ Thu Nov 07, 2013 11:46 pm ] |
| Post subject: | Re: wtb cush for a 4.5 marchesini |
The bushings are different from the std. Ducati cush [thinner] and you have to shorten the drive pins but the Duc carrier will work. My 851/955 was like that. |
|
| Author: | pantah_good [ Fri Nov 08, 2013 10:26 am ] |
| Post subject: | Re: wtb cush for a 4.5 marchesini |
One of Cranky's many missions is to get a supply of the Marchesini type rubber bushings made. They are now un-obtainium. If you want Ti drive pins, they are available here: https://tpoparts.com/cat093/index.php?route=product/product&keyword=drive%20pins&category_id=0&description=1&product_id=262 They will also need to be shortened and the Ti threads going into the aluminum carrier are very grabby. Left handed as well, if I recall. Required lots of never seize and burnishing of threads. Bill |
|
| Author: | huit [ Fri Nov 08, 2013 7:13 pm ] |
| Post subject: | Re: wtb cush for a 4.5 marchesini |
I tried an 851 sprocket carrier no dice it is about an inch/25mm too big. Maybe a little monster carrier? |
|
| Author: | graeme [ Fri Nov 08, 2013 7:25 pm ] |
| Post subject: | Re: wtb cush for a 4.5 marchesini |
I have a 696 carrier if that is any help? If it will help you can have it for the cost of the post. (from Brisbane Aust) Graeme |
|
| Author: | pantah_good [ Fri Nov 08, 2013 8:37 pm ] |
| Post subject: | Re: wtb cush for a 4.5 marchesini |
Hi Paul, How do you mean "too big". My wheel is a 6" wide, going onto an '88 851. It needed a carrier off a '95 type 900ss SP with the wider wheel for proper sprocket offset (about 19mm). What is your wheel and what is it going on? I have a carrier off a '02 620 Monster with about 6mm less sprocket offset, that you can also have for shipping, if that will would help. Bill |
|
| Author: | huit [ Fri Nov 08, 2013 9:09 pm ] | |||
| Post subject: | Re: wtb cush for a 4.5 marchesini | |||
hopefully this will help! Bill it is for tt2, thanks Graeme, but i think the new monster have changed to the bigger style,thanks for the offer
|
||||
| Author: | 618F1 [ Fri Nov 08, 2013 10:54 pm ] |
| Post subject: | Re: wtb cush for a 4.5 marchesini |
Paul. What is the measurement, in mm, center-to-center, from one bolt to another? I have one odd sprocket carrier here with 52mm spacing. If that fits, then it is only the five bolts and the cush rubbers/bushings you will need; what is the diameter of those holes? MikeV |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|