DUCATI TT and F1 FORUM
 
It is currently Fri Dec 15, 2017 5:37 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 84 posts ]  Go to page Previous  1 ... 5, 6, 7, 8, 9  Next
Author Message
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Tue Aug 09, 2011 10:14 pm 
Offline

Joined: Mon Oct 04, 2010 7:47 am
Posts: 100
Images: 0
Hi Rich,
Were you able to make the gasket work for the fuel tank? Your bike is 3.6 pounds lighter then mine. Put some pictures of it on the forum.

Steve,
How much does the yellow bike weight.

Barber should be great fun, looking forward to seeing everyone.

Palmer


Top
 Profile Personal album  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Thu Aug 11, 2011 12:08 am 
Offline

Joined: Sat Oct 16, 2010 7:34 pm
Posts: 65
Location: Southwick, Massachusetts USA
Hi Gary,

Yes, thanks so much. It helped alot. I was able to make a good tank filler cap gasket with what you sent. I haven't ridden it yet with a full tank and lots of swishing so I'm not 100% sure it is tight, but it seems good so far. I need a shakedown run before Barber.

I'm ashamed to say I haven't been able to post pictures yet and I have lots of them. Last few times I tried and failed. I still need to figure it out.

I was a bit surprised and happy it weighed only 322 lbs. I remember it was 335 back in the day.
Rich


Top
 Profile  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Thu Aug 11, 2011 7:04 am 
Offline
User avatar

Joined: Sun Aug 08, 2010 4:37 pm
Posts: 361
Images: 6
Location: Ottawa, Ontario, The Great White North
Hey, Rich:

Should be easy (although not as intuitive as it could be)..

Below the area used to compose your post (you may have to scroll down to see it) there are two tabs: 'Options' and 'Upload Attachment'. Go to the 'Upload Attachment' tab and hit the 'Browse' button to select from your hard drive the image you want to post. 'Add the file' and then browse for the next one. 'Place inline' is optional. but helpful if you want to change the order in which the images uploaded appear.

There's no size limit set, but I've had the forum time-out when I upload an image greater than 2mb.

Let me know if you still have problems, OK?

Regards,

_________________
Steve Munro
loudbike
http://www.loudbike.com
http://www.vintagemotorcyclesforsale.com


Top
 Profile Personal album  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Fri Aug 19, 2011 11:38 pm 
Offline

Joined: Sat Oct 16, 2010 7:34 pm
Posts: 65
Location: Southwick, Massachusetts USA
Hi Steve,
Thanks for the advice. It appears I was succesful in posting some pictures of my 750F1 in the image section.
Rich


Top
 Profile  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Mon Aug 22, 2011 7:16 pm 
Offline
User avatar

Joined: Sun Nov 28, 2010 4:13 am
Posts: 613
Images: 0
Location: Sydney, Australia
It looks like the Loudbike F1 800 has achieved "Legendary Status" on ebay. Sadly the Loudbike logo has been edited from the picture.

Attachment:
File comment: eBay image
CCopy.jpg
CCopy.jpg [ 35.82 KiB | Viewed 1175 times ]


eBay link http://www.ebay.com.au/itm/DUCATI-800-F ... 2c5ec46690

The Legendary DUCATI 800 F1 Quality Print (A3 - 11.6 x 16.5 INCHES) with Gloss Laminate encapsulating & protecting this poster making this ideal for the workshop, garage, home, office etc. This will last you for years to come! AMAZING VALUE & QUALITY BID WITH CONFIDENCE All posters capture the full detail of the motorcycle & are shipped in a Strong Postal Tube for protection! (Picture frame Not Included) Please see my other listings for more motorcycle posters! I will combine postage for 2 up to 6 posters for the same shipping cost as 1.
Thanks for looking.


Original image posted earlier in this thread.
Attachment:
File comment: Original image
RC.JPG
RC.JPG [ 2.96 MiB | Viewed 1175 times ]


It is a very nice looking bike Steve!

_________________
Mike, Sydney Australia
https://www.facebook.com/groups/CarburetorTuningTool/


Top
 Profile Personal album  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Tue Aug 23, 2011 11:19 pm 
Offline

Joined: Sat Oct 16, 2010 7:34 pm
Posts: 65
Location: Southwick, Massachusetts USA
One of the best looking bikes I've ever seen.
Rich


Top
 Profile  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Wed Aug 31, 2011 1:12 pm 
Offline

Joined: Sun Oct 17, 2010 2:24 pm
Posts: 29
Images: 4
Surely the most sincere form of flattery....Steve you must be proud


Top
 Profile Personal album  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Wed Aug 31, 2011 3:35 pm 
Offline
User avatar

Joined: Sun Aug 08, 2010 4:37 pm
Posts: 361
Images: 6
Location: Ottawa, Ontario, The Great White North
Thanks, guys - serious blushing going on..
..But it goes as as it looks (if not better) - and Mr. Palmer gets the credit for that..

Regards,

_________________
Steve Munro
loudbike
http://www.loudbike.com
http://www.vintagemotorcyclesforsale.com


Top
 Profile Personal album  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Thu Oct 13, 2011 9:45 pm 
Offline

Joined: Mon Oct 04, 2010 7:47 am
Posts: 100
Images: 0
WOW, Barber was great fun. It was really good to see everyone and boy what a great track to ride. We had a lot of engine issues in getting the bike ready for the Barber event and actual had to build the motor like twice after some experimental parts failed at a test and tune trackday two weeks before Barber. We ended up with a mild 86 hp motor that ran good all weekend. The grid was pretty full with 33 bikes in BOT3 class and I got to start toward the middle in each of the two races on row 6 on Saturday and row 5 on Sunday (I haven't had to start that far back in years) I ended up with a 3rd on Saturday and a 4th Sunday which was all great fun.
Palmer


Top
 Profile Personal album  
 
 Post subject: Re: Palmer / Munro F1 Hot-Rod Build-Off
PostPosted: Fri Oct 14, 2011 2:47 am 
Offline

Joined: Sun Nov 07, 2010 10:54 pm
Posts: 425
Location: Brisbane
Well done Gary,
I was watching the results and you did very well.

http://www.ahrma.org/ahrma_pdfs/results ... b_day1.htm

http://www.ahrma.org/ahrma_pdfs/results ... b_day2.htm

I've been watching the site for any info of how you all went, you were the only name I recognised.

Thanks for the report, And to Steve for the pictures and videos.

Regards
Graeme


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 84 posts ]  Go to page Previous  1 ... 5, 6, 7, 8, 9  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL