DUCATI TT and F1 FORUM
 
It is currently Fri Mar 29, 2024 4:25 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 12 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Wed Aug 31, 2016 9:11 pm 
Offline
User avatar

Joined: Mon Jul 11, 2016 8:44 pm
Posts: 94
Location: Atlanta
If anyone has a side stand that will fit my 750 F1, please PM me.

Thanks!

:D


Top
 Profile  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Wed Aug 31, 2016 11:32 pm 
Offline

Joined: Thu Oct 14, 2010 11:23 am
Posts: 1803
Real F1 sidestands are very rare now. I have used an Alazurra after cutting some of the heavy tabs off it. And I had to remove the center stand to install it. It is probably about 1 and 1/2 inch too short, hard to get to under the muffler with a boot on, and it is just plain spooky when it is leaned over.

Ed Milich would be a good source to check with if you want to go that route.

MikeV


Top
 Profile  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Thu Sep 01, 2016 7:51 pm 
Offline
User avatar

Joined: Mon Jul 11, 2016 8:44 pm
Posts: 94
Location: Atlanta
Thanks, Mike.

Ed has no further stands.

It would be easier for me adapt an Alazzurra stand than try to make a completely new one. First I need to find one...


Top
 Profile  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Fri Sep 02, 2016 8:12 am 
Offline

Joined: Thu Oct 31, 2013 2:04 pm
Posts: 28
I can send a picture of mine so you can have one made if you like.
Tom


Top
 Profile  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Sun Sep 04, 2016 11:43 pm 
Offline
User avatar

Joined: Tue Mar 18, 2014 10:03 am
Posts: 360
Hello Beas42...
If you could post, or anyone else for that matter, a detailed drawing of the side stand, I'll take a shot at reproducing one... or more.
Regards...
Flattop900


Top
 Profile  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Mon Sep 05, 2016 8:06 am 
Offline

Joined: Thu Oct 31, 2013 2:04 pm
Posts: 28
Pics taken with muffler removed. Bracket holes 64 mm center to center, Bolt center to sidestand end 13.5 in, bolt to spring mount 5 in.


Attachments:
SS3.jpg
SS3.jpg [ 483.94 KiB | Viewed 2185 times ]
SS2.jpg
SS2.jpg [ 452.7 KiB | Viewed 2185 times ]
SS1.jpg
SS1.jpg [ 567.23 KiB | Viewed 2185 times ]
Top
 Profile  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Mon Sep 05, 2016 6:00 pm 
Offline
User avatar

Joined: Mon Jul 11, 2016 8:44 pm
Posts: 94
Location: Atlanta
flattop900 wrote:
I'll take a shot at reproducing one... or more.


You would be my hero if you did!

:D


Top
 Profile  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Tue Sep 06, 2016 5:30 pm 
Offline
User avatar

Joined: Tue Mar 18, 2014 10:03 am
Posts: 360
Hello...
Did a little digging and found an Alazzurra side stand. Going to need more info on the original, most important, the angle of the bend in the bracket. If it is the same as the Alazzurra then only a leg has to be made. Speaking of, is the leg tubing or solid? What diameter? Is that a stiffening brace I see in the pictures? Is the face of the foot in the same plain as the face of the clevis? What angle is the foot at? Are the raised or thicker areas where the mounting holes are, present or machined flush to fit flat against the frame?
Regards...
Flattop900


Attachments:
sidestand bracket 002.JPG
sidestand bracket 002.JPG [ 5.05 MiB | Viewed 2134 times ]
sidestand bracket 001.JPG
sidestand bracket 001.JPG [ 5.33 MiB | Viewed 2134 times ]
Top
 Profile  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Fri Sep 09, 2016 1:30 pm 
Offline

Joined: Wed Nov 17, 2010 5:43 pm
Posts: 60
Images: 1
The bracket is the same as the Allazura. The stand is tubular and longer than the Ally stand. Spring is different too.


Top
 Profile Personal album  
 
 Post subject: Re: ISO: F1 / Alazzurra / TT Side Stand
PostPosted: Sat Sep 10, 2016 4:19 pm 
Offline

Joined: Thu Oct 31, 2013 2:04 pm
Posts: 28
Plate part# 037712250, side stand part # 037712500. Plate bend angle 40 deg, plate mount holes raised area .150 in high,1.035 diam. Stand diam .810 in, has brace to strengthen The foot is not in the same plane as the clevis, is angled slightly to the front of the mc. The angle of the foot to the shaft is 40 deg.


Attachments:
Stand 2.jpg
Stand 2.jpg [ 472.42 KiB | Viewed 2053 times ]
Stand 1.jpg
Stand 1.jpg [ 356.48 KiB | Viewed 2053 times ]
Plate 1.jpg
Plate 1.jpg [ 777.8 KiB | Viewed 2053 times ]
Plate 2.jpg
Plate 2.jpg [ 700.1 KiB | Viewed 2053 times ]
Plate 3.jpg
Plate 3.jpg [ 694.4 KiB | Viewed 2053 times ]
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 12 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Bing [Bot] and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL
[ Time : 0.079s | 18 Queries | GZIP : Off ]