Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum
http://www.ducatittandf1.com/

Alazzurra big mistake 440!
http://www.ducatittandf1.com/viewtopic.php?f=25&t=11863		 Page 1 of 6
Author:  583 [ Mon Dec 17, 2018 3:47 pm ]
Post subject:  Alazzurra big mistake 440!
Image
Hallo Everybody.
With the winter racing break I start a new project.
The above engine is the one I race with for years, now replaced with the 513cc.
My idea is to assemble a stock Alazzurra for daily use or for aving fun on "curvy street".

So I start rebuilding everything and only when I put the engine on the new frame I check for valve clearance. Everything ok except for this:
Image
Author:  583 [ Tue Dec 18, 2018 5:06 am ]
Post subject:  Re: Alazzurra 540
..and these
https://www.flickr.com/photos/156916018 ... res/PDz7NT
Author:  618F1 [ Wed Dec 19, 2018 9:09 pm ]
Post subject:  Re: Alazzurra 540
Well, you got the miles in, but this makes me wonder what the rod bearings look like, and the clutch, and.......?

MikeV
Author:  583 [ Thu Dec 20, 2018 1:43 pm ]
Post subject:  Re: Alazzurra 540
..and...
Image

Image

Both exhaust valves hit, gently, the piston.
In years of racing I never heard about any strange head noise.

Notice, by the cut on the vertical cylinder, that his is a 350ss 540 kit adapted to an Alazzurra 350.
Maybe this is wy valves "lick" the pistons and of course a lack of maintenance.
Thank you MikeV for your reply, I belive, but I hope not, that going deeper with this engine I will need to refresh everything.
Ciao
Filippo
Author:  ducadini [ Fri Dec 21, 2018 4:04 pm ]
Post subject:  Re: Alazzurra 540
About Your kit, I think it is one of the early GioCaMoto kits, made for the Pantah and Alazzurra 350's with exhaust on front.
Someone used it on a 350 SS or (in my case) on a 350 Elephant, hence the rough cutout on the REAR to clear the exhaustport.
Later kits ( even the 600-700 kit) had the cutout on both sides.
Great work keeping those litlle engines alive.
Should be interesting having them both on the powerbench to compare although the bigger valves should be a indication.

Buon natale

ciao
ducadini
Author:  583 [ Sat Dec 22, 2018 4:17 am ]
Post subject:  Re: Alazzurra 540
Ciao Ducadini e grazie.
You're right, I just get confused on looking the pictures of the engine and decided was a 350ss kit.
But I was wrong.
So Giocamoto kit for Alazzurra definitely.
Yes as before I hope to check this engines, maybe the 513 on a powerbench.
Buone feste!!
Filippo
Author:  583 [ Sat Feb 16, 2019 2:58 pm ]
Post subject:  Re: Alazzurra 540
Image

Image

Hi everybody
Finally we put hands on heads.
Author:  flattop900 [ Sun Feb 17, 2019 9:26 am ]
Post subject:  Re: Alazzurra 540
Looking good Filippo. Did you resolve the valve / piston clearance issue?
Regards....
Flattop
Author:  583 [ Mon Feb 18, 2019 2:00 pm ]
Post subject:  Re: Alazzurra 540
Hi Flattop
Not yet checked the clearance.
But valves job is done and also a little of porting on head.
Image
Above the orizzontal head with a little of removed material.
I find heads with this rough porting attempt.

Image
Same head but ported.
Author:  583 [ Wed Feb 20, 2019 1:47 pm ]
Post subject:  Re: Alazzurra big mistake 440!
Shane on me.
For same reason I was sure this engine was 540 c.c.
Yesterday, with the engine open I misured the bore, just because samething wrong was flipping on my brain.
So true bore is 74 mmm
Image

So I have a 440 cc Giocamoto kit.

No problem, still a nice engine for have fun!

Filippo
Page 1 of 6 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/