DUCATI TT and F1 FORUM
 
It is currently Thu Mar 28, 2024 6:01 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Spacer
PostPosted: Thu Sep 13, 2018 3:53 pm 
Offline
User avatar

Joined: Tue Mar 18, 2014 10:03 am
Posts: 360
Hello...
I am installing a new set of straight cut primary gears into a 600TL engine. What I need to know is the thickness of the spacer that goes onto the main shaft before the pressure plate. All of the parts manuals give the size for the one that goes on before the basket and gear, (5mm) but no reference to the one in question.
Regards....
Flattop


Top
 Profile  
 
 Post subject: Re: Spacer
PostPosted: Fri Sep 14, 2018 11:01 am 
Offline

Joined: Wed Aug 27, 2014 3:36 pm
Posts: 325
Hi Flattop
what an interesting topic!
https://www.ducatimeccanica.com/cagiva_ ... laz_06.htm
Please for the 5mm spacer you mean the n°28 on the above link?
and which is the number of the spacer you are asking for?
ciao
Filippo


Top
 Profile  
 
 Post subject: Re: Spacer
PostPosted: Fri Sep 14, 2018 12:09 pm 
Offline
User avatar

Joined: Tue Mar 18, 2014 10:03 am
Posts: 360
Hi Filippo....
Sorry, I should have posted this picture earlier, but the manual is in pdf and won't allow page extraction. I had to photograph it off my laptop. The only parts manual I've found to show this diagram is the 350/650 Elefant. The Alazzurra manual is a little misleading. I'm installing the steel basket, later clutch. The spacer in question is #30.
Thank you for the reply....
Flattop
P.S.
How are things in beautiful Italy?


Attachments:
650 wet clutch..JPG
650 wet clutch..JPG [ 4.99 MiB | Viewed 1856 times ]
Top
 Profile  
 
 Post subject: Re: Spacer
PostPosted: Fri Sep 14, 2018 3:28 pm 
Offline

Joined: Thu Oct 14, 2010 11:23 am
Posts: 1802
A bit pressed for time right now, but it is the same washer that goes with #29, found between the two bearings in the basket hub. About 2.0mm thick. As long as the bottom pressure plate clears the basket (I have seen them shoved right to the metal there, and then the plate can't spin) you will be OK. MikeV

CORRECTION. Meant it is the washer in the #31 on the schematic. About 1.5 to 2.0mm thick, with correct ID. It is in all the primary gears. MikeV


Top
 Profile  
 
 Post subject: Re: Spacer
PostPosted: Sat Sep 15, 2018 6:57 am 
Offline

Joined: Wed Aug 27, 2014 3:36 pm
Posts: 325
Hi Flattop
I checked on a spare Alazzurra 350 clutch I have, but the shaver you need is missing on that clutch. I'm sorry.
I will find it when I will looking for other engine related stuff.
In Italy is still hot weather, good for the beach!
Ciao
Filippo


Top
 Profile  
 
 Post subject: Re: Spacer
PostPosted: Sun Sep 16, 2018 10:31 am 
Offline
User avatar

Joined: Tue Mar 18, 2014 10:03 am
Posts: 360
Thanks guys. Found one on the shelf, moving forward.
Flattop


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL
[ Time : 0.044s | 19 Queries | GZIP : Off ]