|
View unanswered posts | View active topics
Author |
Message |
583
|
Post subject: Re: Pantah project Posted: Tue Jan 02, 2024 2:52 pm |
|
Joined: Wed Aug 27, 2014 3:36 pm Posts: 346
|
Hi Huit happy new year to you Very good looking engine, in looking at your previous post you mentioned a dry clutch but now i don't know when you switch on wet clutch. I'm curious to see the look of the fairing once everiyhing is in place. Enjoy your project Filippo
|
|
Top |
|
|
huit
|
Post subject: Re: Pantah project Posted: Tue Jan 02, 2024 8:41 pm |
|
Joined: Sat Oct 29, 2011 3:38 pm Posts: 836
|
Filippo, Thanks for the comments, I had to go back to my first post to check to make sure I put in wet clutch Paul
|
|
Top |
|
|
583
|
Post subject: Re: Pantah project Posted: Thu Jan 04, 2024 8:27 am |
|
Joined: Wed Aug 27, 2014 3:36 pm Posts: 346
|
Hi Paul It's my fault on your first post you report about a wet clutch Apologies Filippo
|
|
Top |
|
|
huit
|
Post subject: Re: Pantah project Posted: Thu Jan 04, 2024 8:03 pm |
|
Joined: Sat Oct 29, 2011 3:38 pm Posts: 836
|
No apology needed! How’s your Tt coming along?
|
|
Top |
|
|
583
|
Post subject: Re: Pantah project Posted: Fri Jan 05, 2024 7:44 am |
|
Joined: Wed Aug 27, 2014 3:36 pm Posts: 346
|
Quote: huit wrote: No apology needed! How’s your Tt coming along? Hi Paul still from my side because i'm working abroad. I know the guys are proceeding with Head holder to machine valves seat.i will update as soon i receive pics. Regards Filippo
|
|
Top |
|
|
huit
|
Post subject: Re: Pantah project Posted: Sat Jan 06, 2024 3:04 pm |
|
Joined: Sat Oct 29, 2011 3:38 pm Posts: 836
|
Did a test fit after shock was tacked in place, close but no cigar I need to move the left tab at the top over about 6mm Mounted the the right side exit exhaust so I can start to make the rest of the exhaust
Attachments: |
IMG_3028.jpeg [ 2.53 MiB | Viewed 56044 times ]
|
|
|
Top |
|
|
618F1
|
Post subject: Re: Pantah project Posted: Sat Jan 06, 2024 8:36 pm |
|
Joined: Thu Oct 14, 2010 11:23 am Posts: 1861
|
And i am waiting to see how the camshaft pulleys are aligned! MikeV
HNY Paul.
Ooh. I like that muffler.
|
|
Top |
|
|
huit
|
Post subject: Re: Pantah project Posted: Sun Jan 07, 2024 9:46 am |
|
Joined: Sat Oct 29, 2011 3:38 pm Posts: 836
|
Mike, I haven’t done the cam timing yet, I set the timing mark on the vertical pulley to its normal position then rotated the cam to correct position and put in 3 cap screws, tightened the screws put in the rest of the screws installed the belts and rolled over the motor, no collisions! I had to remove a little material off the top of the pistons, the plugs were too close for comfort. That muffler makes the bike!
|
|
Top |
|
|
huit
|
Post subject: Re: Pantah project Posted: Fri Feb 23, 2024 8:47 pm |
|
Joined: Sat Oct 29, 2011 3:38 pm Posts: 836
|
Going to the painters tomorrow!
Attachments: |
Ducati CR.jpeg [ 802.86 KiB | Viewed 31999 times ]
|
|
|
Top |
|
|
618F1
|
Post subject: Re: Pantah project Posted: Fri Feb 23, 2024 9:08 pm |
|
Joined: Thu Oct 14, 2010 11:23 am Posts: 1861
|
I don’t see how they can improve on that! No headlight - a track bike? MikeV
|
|
Top |
|
|
Who is online |
Users browsing this forum: No registered users and 2 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|
|