DUCATI TT and F1 FORUM
 
It is currently Thu Mar 28, 2024 3:56 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Cam End Caps from Sports Motorcycles
PostPosted: Fri Mar 30, 2012 5:47 pm 
Offline

Joined: Thu Oct 14, 2010 11:23 am
Posts: 1802
Here are the new caps made by Glyn Robinson, of the new "Sports Motorcycles" in the UK. They are cnc'd and then blasted to soften the look a bit, so they look more vintage than the photo on the site. 8mm tap holes, and bearing already installed. I think $180 a set is good deal. MikeV
Attachment:
cam caps.JPG
cam caps.JPG [ 554.87 KiB | Viewed 8332 times ]


Top
 Profile  
 
 Post subject: Re: Cam End Caps from Sports Motorcycles
PostPosted: Sat Mar 31, 2012 6:14 am 
Offline

Joined: Wed Apr 27, 2011 4:56 pm
Posts: 79
618F1 wrote:
Here are the new caps made by Glyn Robinson, of the new "Sports Motorcycles" in the UK. They are cnc'd and then blasted to soften the look a bit, so they look more vintage than the photo on the site. 8mm tap holes, and bearing already installed. I think $180 a set is good deal. MikeV
Attachment:
cam caps.JPG



I was thinking of getting a set made up by a chap I know in Poland who is making a couple of bits and bobs for me now! I bet he could do it cheaper than Sports Motorcycles :P


Top
 Profile  
 
 Post subject: Re: Cam End Caps from Sports Motorcycles
PostPosted: Sat Mar 31, 2012 11:09 am 
Offline

Joined: Wed Apr 27, 2011 4:56 pm
Posts: 79
I have noticed on my original SS cam end caps there is a small hole on the inside which allows oil to get behind the bearing. And on these Sports ones and the original race ones the oil supply is from the outside, does this external oil supply come from the Oil cooler?


Top
 Profile  
 
 Post subject: Re: Cam End Caps from Sports Motorcycles
PostPosted: Sat Mar 31, 2012 12:49 pm 
Offline

Joined: Thu Oct 14, 2010 11:23 am
Posts: 1802
Yes, George, these are for the external lines directly from a cooler. Usually the race engines had the stock oil supply lines through the cases/cylinders/heads blocked off. NCR heads have them blocked. And Steve says the flow is also restricted, because the valve train gets too much oil in stock form. For me that explains why the locating dowels for oil supply have much smaller holes in recent years. Lou and Steve will know more about this than me, and others will chime in I am sure. MikeV


Top
 Profile  
 
 Post subject: Re: Cam End Caps from Sports Motorcycles
PostPosted: Sat Mar 31, 2012 1:01 pm 
Offline

Joined: Wed Apr 27, 2011 4:56 pm
Posts: 79
618F1 wrote:
Yes, George, these are for the external lines directly from a cooler. Usually the race engines had the stock oil supply lines through the cases/cylinders/heads blocked off. NCR heads have them blocked. And Steve says the flow is also restricted, because the valve train gets too much oil in stock form. For me that explains why the locating dowels for oil supply have much smaller holes in recent years. Lou and Steve will know more about this than me, and others will chime in I am sure. MikeV


Cheers Mike!

er.... is that a bad thing?.... mechanical components whizzing whirring and whacking up and down at very high velocities getting too much oil!


Top
 Profile  
 
 Post subject: Re: Cam End Caps from Sports Motorcycles
PostPosted: Sat Mar 31, 2012 2:54 pm 
Offline

Joined: Tue Oct 05, 2010 9:21 am
Posts: 274
Images: 0
The stock F1/pantah/alley has a restictor in the feed right abover the oil filter in the form of a drift pin. The diameter is .046 inches. When bypassing directly to heads from coolers I use a .046" restrictor directly on each head feed in the banjo bolt. This increases the supply (theortically double). Too much (non restricted) oil turns in to foam and cannot get back down to the sump. Not good!


Top
 Profile Personal album  
 
 Post subject: Re: Cam End Caps from Sports Motorcycles
PostPosted: Sun Apr 01, 2012 4:45 am 
Offline

Joined: Wed Apr 27, 2011 4:56 pm
Posts: 79
CrankyRoller wrote:
The stock F1/pantah/alley has a restictor in the feed right abover the oil filter in the form of a drift pin. The diameter is .046 inches. When bypassing directly to heads from coolers I use a .046" restrictor directly on each head feed in the banjo bolt. This increases the supply (theortically double). Too much (non restricted) oil turns in to foam and cannot get back down to the sump. Not good!



Aha I undestand now thanks for the explanation :D


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL
[ Time : 0.043s | 18 Queries | GZIP : Off ]